This Standard covers specialized fittings made of ABS or PVC intended for DWV applications and specifies requirements for materials, dimensions and other physical characteristics, and markings.
This Standard covers standard fitting geometries and laying lengths for plastic fittings intended for use as internal cleanout fittings for ABS and PVC schedule 40 plastic drain, waste and vent (DWV) pipe and specifies requirements for materials, physical characteristics, performance testing and marking and identification.
This standard covers electrical or high‐density magnetic anti‐scale or water conditioning appliances in nominal pipe sizes from 12.7 mm (0.5 in) through 406.4 mm (16 in) and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers copper wrought solder‐filled joint fittings for installation on copper tubing and specifies requirements for materials, physical characteristics, performance testing, and markings. This Standard serves to supplement the provisions of IAPMO IS 3.
This Standard covers water distribution manifolds for residential and commercial, hot and cold, water distribution systems, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers automatic water leak detection and control devices and automatic water leak detection and shut‐off devices in sizes NPS‐1/4 to NPS‐10 and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers water treatment equipment drain connectors and specifies requirements for materials, physical characteristics, performance testing, and markings. This Standard covers water treatment equipment drain connectors, which are comprised of a reducer assembly, and air gap reducer assembly or a reducer wye. The reducer assembly and the air gap reducer assembly is designed to attached to the plumbing drainage system using a drainage tee, a diversion tee or a trap adapter. Such devices are intended to provide a transition connection from an appliance or water treatment equipment to the plumbing drainage system.
This Standard covers elastomeric gasketed and rubber‐ring joint fittings intended for use in hot and cold potable water installations and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers test caps and test gates with ABS, PVC, or rubber couplings with stainless steel band housings and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers combined hand‐washing systems comprised of electronically actuated soap dispensers, faucets, and hand air‐dryers, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers water heater supply shutoff valves with thermal expansion control valves for use on closed plumbing systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers vacuum toilet systems intended for recreational vehicle applications and specifies requirements for materials, physical characteristics, performance testing, and markings. The vacuum toilet systems covered by this Standard are those systems which are connected to the potable water system and a Standard waste holding tank intended for use in recreational vehicles when installed in accordance with applicable code requirements.
This Standard covers flexible elastomeric mechanical fittings for use with plain end drain, waste, and vent (DWV) and plain end sewer (tubular waste) pipe and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers shower/steam panels, enclosures for showers and tub/shower combinations, bathtubs and tub/shower combinations with glass pressure‐sealed doors, and floor‐mounted showers intended for new and retrofit applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers wash fountains and lavatory systems with or without water closets and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers pool shells constructed from fiberglass reinforced plastic (FRP) materials and specifies requirements for materials, physical characteristics, performance testing, and markings. This Standard applies to FRP pool shells whose bottom is fully supported by soil or the structural system of the building in which it is to be installed. The sides of these types of pool shell are designed to span from the bottom to an FRP bond beam positioned around the perimeter at the top of the pool shell.
This standard applies to zero waste water reverse osmosis systems and zero waste retrofit kits to adapt to existing reverse osmosis systems. It covers definitions, general requirements, performance requirements, and marking for such systems.
This Standard covers flushing and non-water-consuming urinals with mechanical traps and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers special fittings with strainers intended for water closet fill valves and specifies requirements for materials, physical characteristics, performance testing, and markings.
This IGC covers the test methods and performance requirements applicable for freeze protection devices with test cocks. These devices are intended to provide intermittent freeze protection and not as winterization devices for cold weather climates.
The provisions of the IGC are to allow for the establishment of technology for Plastic DWV to Sewer Adapters. The provision of the IGC is not intended to prevent the use of alternate design, assembly configuration, method or material, provided any such alternate meets the performance and minimum specification criteria outlined herein.
The purpose of this standard is to: (a) establish acceptable criteria for solid waste containment interceptors; (b) serve as a guide for producers, distributors, architects, engineers, contractors, installers, inspectors, and users; (c) promote understanding regarding materials and manufacturing of solid waste containment interceptors; and (d) provide for markings that identify solid waste containment interceptors that comply with this Standard.
This standard covers supply stops with integral water hammer arresters and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers shower arm adapters that allow connection to copper water tubes outside of the finished wall and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers gravity fed water distribution manifolds for trap primers utilized in conjunction with trap primers to distribute gravity fed water to multiple p‐traps for maintaining the p‐trap’s water seal and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers aerobic bacterial generators intended for installation in septic tanks for restoring and preserving the soil’s ability to absorb, treat, and dispose of the effluent and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers combination fill valve and hydraulic actuated flush valve intended for use in gravity type water closets and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers oil/water separators and coalescing plate separators designed to remove petroleum based oils from storm or process water and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers hot and cold water distribution female threaded outlets intended for use up to 300 psi water pressure at a maximum working temperature of 180°F and specifies requirements for materials, physical characteristics, performance testing, and markings. Female threaded outlets covered by this standard are connected to copper or stainless steel water supply tubing used in conjunction with supply stop valves made to the requirements of ASME A112.18.1/CSA B125.1. The components covered by this standard are intended for use in residential and commercial, hot and cold, potable water distribution systems.
This Standard covers roof drains with integral overflows or air vents and specifies requirements for materials, physical characteristics, performance tests, and markings.
This standard covers mechanically applied epoxy barrier coatings to the interior of pressurized (closed) water piping systems and specifies requirements for materials, physical characteristics, performance testing, and markings. This standard does not cover design or testing of epoxy barrier coating for use with fire sprinkler piping system
This Standard specifies requirements for the installation of thrust blocking for ductile iron pipe with elastomeric gasketed joints and fittings and PVC piping with solvent cemented or elastomeric gasketed joints intended for cold water building supply and yard piping. Thrust blocks covered by this standard prevent separation of joints and pipe movement by transferring the resultant thrust force at a bend to the undisturbed soil behind the thrust block. The bearing strength of the soil is expressed in pounds per square foot. Therefore, the area behind the thrust block must engage enough soil area to resist the resultant thrust force at a change in direction.
This Standard covers condensate traps and overflow switches intended for use in air conditioning system applications and specifies requirements for materials, physical characteristics, performance testing, and markings. Products covered by the scope of this standard may include waterless condensate traps, special purpose PVC fittings and/or condensate trap and/or overflow switch assemblies.
This standard covers elastomeric elbows and tees used in the connection of common household drain, waste and vent pipes for above ground non-pressure repair applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers overflow pans for washing machines, water heaters, and other appliances and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers polyethylene sleeved‐corrugated stainless‐steel tubing (PE‐CSST) intended for use in fuel gas piping systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers bracing systems intended for securing water heaters to wood wall structures (i.e., wood studs) and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers the method of application, type of materials and other significant properties in addition to general description of materials used. Certain features of manufacturing of the finished product are also given, together with the markings for identification of the finished product. The factory applied AL and PE or PEX coated SDR9 PEX tubing, covered by this standard, is intended for use in all installations when installed in compliance with the Uniform Plumbing Code as published by the International Association of Plumbing and Mechanical Officials and the manufacturer’s installation instructions. All polyethylene (PE) or crosslinked polyethylene (PEX) coating shall be applied in the plant expressly for this work with approved materials. The adhesive and PE or PEX coating shall be applied in one continuous operation by passing aluminum wrapped tubing through a machine expressly designed for this purpose. The coating described in this standard is designed to protect and support the distribution tubing. Stripping of coating to expose PEX tubing prior to applying fittings shall not reduce, affect or damage the outside diameter of the PEX tubing.
This Standard covers in-line devices used for filtration of storm water runoff in structure downspouts and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers vertical leaching systems to be used in conjunction with septic wastewaters tanks and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers building/structure installed breathing air replenishment systems (BARS) to be used in conjunction with self‐contained breathing apparatuses (SCBA) and specifies requirements for materials, physical characteristics, performance testing, and markings. This standard serves to supplement the provisions of Appendix F in the Uniform Plumbing Code (UPC).
This standard covers wastewater diverter valves and diversion systems and specifies requirements for materials, physical characteristics, performance testing, and markings. Wastewater diverter valves covered by this Standard can be used in alternate water source systems for indoor and outdoor non‐potable uses.
This Standard covers lavatory or sink traps with or without removable filter or cleaning device for use in commercial and residential applications, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers drinking water fountains with or without chiller or heater and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers corrugated stainless steel hot- and cold- water distribution systems intended for use in 1012.8 kPa (147 psi) water service up to and including a maximum working temperature of 100°C (212°F) and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers demand driven storm water diversion systems and associated electrical/mechanical control components intended for residential and commercial applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers wood plumbing fixtures and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers physical requirements and tests for types of materials, thickness, dimensions and other significant properties in addition to general description of materials used.
This Standard covers high pressure shielded couplings which have a stated working pressure of 103 kPa (15 psi) or greater for use with hubless cast iron soil pipe and fittings and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers (a) aluminum-polypropylene (AL-PP) composite pipe consisting of a core of extruded polypropylene (PP) surrounded by a welded aluminum (AL) tube joined by a melt adhesive; and (b) fittings intended for use with the AL-PP composite pipe.
This standard applies to mechanical automatic water supply shutoff devices and component(s) (see Part IV, Definitions), hereinafter referred to as systems and component(s) constructed entirely of new, unused parts and materials, which is intended for use with electric water heaters, bathtubs, shower heads, lavatories, sinks, or water closets. This standard covers, reference standards, definitions, general requirements, materials, test requirements, and marking and identification for water flow shut off devices.
This Standard covers temperature-actuated flow-reduction devices and systems intended to be installed in tub spouts or immediately upstream of shower heads and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers odor-removing systems intended for installation for water closets and urinals and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers requirements for water closets with an overflow and specifies requirements for materials, physical characteristics, performance testing, and markings.
The purpose of this standard is to provide the minimum design and performance criteria for water closet with an integral rinse station. This standard is not intended to be a specification guide nor is it intended to restrict design.
This standard covers minimum requirements for materials in the construction of whirlpool bathtub with pressure sealed doors and optional reservoir/waste tank(s), and to prescribe minimum test requirements for the performance of these devices, general requirements and methods of marking and identification.
This Standard covers excess-flow shutoff devices intended for use in water supply systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers corrugated thermoplastic tanks intended for septic, grease interception, storm-water collection, and potable and non-potable water storage applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers roof drain terminal outlets used for connecting roof drain downspouts in sizes NPS-2 to NPS-12, and specifies requirements for materials, physical characteristics, performance testing, and markings. Roof drain terminal outlets covered in this Standard are intended for residential, commercial, and industrial applications.
This standard applies pivoting water closet and covers general requirements, strength and performance tests for such products, in addition to method of markings and identification.
This Standard covers wall, ground, post, and floor hydrants without integral backflow preventers and specifies requirements for physical characteristics, performance testing, and markings.
This Standard covers PVC or ABS covers for use with unshielded flexible transition couplings for underground piping systems, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers commercial faucets with integral emergency eye wash units, and specifies requirements for materials, physical characteristics, performance testing, and markings. This unit is comprised of a faucet that contains an integral emergency eye washer station and is plumbed separately and is intended for commercial use only.
This Standard covers stainless steel drainage systems with alternate end connections and specifies requirements for materials, physical characteristics, performance testing, and markings. This standard serves as a supplement to ASME A112.3.1 and addresses end connections requirements that are not covered by the current version of ASME A112.3.1.
This Standard covers systems consisting of bundled synthetic aggregate made of expanded polystyrene (EPS) intended for use in subsurface drainage applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers flexible polyvinylchloride (PVC) gaskets intended to seal the joints between water closets and urinals and sanitary drainage systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers heat exchange systems intended for use in residential and commercial potable water distribution systems, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers pedicure fixtures and specifies requirements for materials, physical characteristics, performance testing, and markings. Pedicure fixtures covered by this Standard can include a massage chair.
This Standard covers ABS and PVC water closet flanges that have a clamping seal for use with floor‐covering membranes and specifies requirements for materials, physical characteristics, performance tests, and markings.
This Standard covers SDR 11 (standard dimension ratio 11) chlorinated polyvinylchloride (CPVC) pipe, tubing, and fittings for use in hot and cold water distribution systems that operate at a maximum working pressure of 690 kPa (100 psi) and a maximum temperature of 82.2 °C (180°F).
This Standard covers thermostatic shower mixing valves with on‐demand hot‐water circulation systems and specifies requirements for materials, physical characteristics, performance tests, and markings.
This Standard covers portable seated personal showering systems and specifies requirements for materials, components, physical characteristics, performance testing, and markings
This Standard covers bedpan liner macerators and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers thermoplastic flexible fittings for connecting water closets and urinals to the sanitary drainage system and specifies requirements for materials, dimensions and tolerances, performance testing, and markings.
This Standard covers plastic shower pans with ABS and PVC DWV pipes bonded by means of an epoxy adhesive and specifies performance tests and markings.
This Standard covers tubing and fittings for special hydronic radiant drywall panels intended for residential and commercial heating and cooling applications and specifies requirements for materials, physical characteristics, performance tests, and markings.
This Standard covers sanitary floor sinks made of carbon steel and intended for draining indirect waste to the sanitary drainage system. It specifies requirements for materials, manufacture, physical characteristics, performance tests, and markings.
This Standard covers pressure relief valves intended for installation in hot- and cold-water distribution systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers support blocks intended for installation on flat roof surfaces for supporting water, gas, condensate or refrigeration piping, electrical conduits, ductwork, roof-top walkways, and mechanical equipment, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers ring gaskets intended to seal the joints between water closets and urinals and sanitary drainage systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers push‐fit fittings intended for use with PVC pipe for irrigation systems, in sizes IPS‐1/2 to IPS‐2, and specifies requirements for materials, physical characteristics, performance testing, and markings. Fittings covered by this Standard are intended for aboveground and buried applications.
This Standard covers flexible continuous wastes intended for connecting lavatories and sinks to the sanitary drainage system and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers potable water hygiene systems consisting of valves and fittings, electronic sensors, actuators, and control devices intended to ensure the hygienic transport of potable water and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers catalytic scale-prevention devices intended for residential and commercial applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers stainless steel flexible expansion joints intended to absorb movements in drain, waste, and vent and sewer systems caused by thermal expansion and contraction and building structural movements, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard (a) covers backwater valves (i) intended for use in horizontal pipe runs (e.g., to floor drains, sewers, and holding tanks); (ii) equipped with a moving sealing element that can be removed with a lifting device; and (iii) having an overall length of the access structure that is more than 600 mm (24 in) from the access opening; and (b) specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers brass compression fittings for polyethylene/aluminum/polyethylene (PE-AL-PE) and polyethylene/aluminum/cross-linked polyethylene (PE-AL-PEX) composite pressure piping in nominal sizes 1014, 1216, 1620, 2025, 2532, 3240, 4050, 5063, 6375, 7590, and 90110 and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers co-extruded polyethylene/aluminium/polyethylene (PE-AL-PE) composite pipes comprising a welded aluminium (AL) tube laminated by a melt adhesive to two layers of polyethylene (PE) in nominal sizes 1216, 1620, 2025, 2532, 3240, 4050, 5063, 6375, 7590, and 90110 and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers co-extruded polyethylene/aluminium/crosslinked polyethylene (PE-AL-PEX) composite pipes comprising a welded aluminium (AL) tube laminated by a melt adhesive to an outside layer of polyethylene (PE) and an inside layer of crosslinked polyethylene (PEX) in nominal sizes 1216, 1620, 2025, 2532, 3240, 4050, 5063, 6375, 7590, and 90110 and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers servo-operated shut-off valves, in sizes NPS-3/8 to NPS-3/4, intended for use in water supply and distribution systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers gate, globe, angle, and check valves in sizes NPS‐1/8 to NPS‐4, with minimum rated working pressures of 860 kPa (125 psi) at 23 ºC (73ºF), intended for use in water supply and distribution systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers stainless steel multi-stall urinals intended for commercial applications (e.g., public amenities) and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard specifies performance requirements for LED lights and LED generators for shower heads, hand-held showers, and aerators.
This Standard covers manifold systems intended for use in residential and commercial applications with a minimum pressure-temperature rating of 690 kPa (100 psi) at 82 ºC (180ºF), and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers water closets with integral self-cleaning systems that operate by introducing liquid chemical cleaning agents into the water channels of the water closet during a specific cleaning cycle, separate from the normal flush cycle.
This Standard covers plumbing and electrical aspects of open colonic irrigation systems and specifies general requirements, materials, physical characteristics, performance test methods, and markings.
This Standard covers metal insert fittings for use with PEX tubing that complies with ASTM F876, or CSA B137.5, and PE-RT tubing that complies with and ASTM F2623 or ASTM F2769, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers cured-in-place point rehabilitation systems for pipe reconstruction and also specifies requirements for materials, physical characteristics, performance tests, and markings
This Standard covers alkaline water – drinking water treatment units intended for use in residential, commercial and food service applications and specifies requirements for materials, performance tests and markings.
This Standard covers vent terminal debris guards intended for installation under solar panels and at the termination point of the vent pipe or stack in residential and commercial buildings’ DWV systems, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers alternate water source systems for single‐family dwellings intended to process water from alternate water sources such as greywater, rainwater, atmospheric generated water, and air conditioning condensate, for use in subsurface and/or surface irrigation and toilet/urinal flushing applications, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers high efficiency oil/water separators intended for residential and commercial applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers ½-NPS to 12-NPS flexible metallic expansion joints intended for use in pressure systems to absorb fluctuations in the system due to thermal expansion and contraction and building structural movements. The standard specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers exposed, accessible, and non-wall penetrating flexible trap arm assemblies that include couplings, directional fittings, and tubular fittings intended for connecting fixture traps to the sanitary drainage system, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers steel reinforced polyethylene rainwater harvesting tanks intended for below ground applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers portable and stationary recirculating shower systems intended for new and retrofit residential, commercial, RV and trailer applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers rooftop adjustable pipe support systems for installation on flat roof surfaces for elevating and securing industrial piping and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers hydronic radiators intended for use in residential and commercial applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers vent pipe plastic membrane funnels intended for installation on vertical vent piping systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers reversible 1-1/2”, 2”, and 3” NPS push fit drain, waste, and vent fittings intended for quick assembly of DWV pipe and fittings applications, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers performance testing of scale prevention devices for differing water samples using a rapid scaling test. The scale prevention devices covered by this standard are intended for residential and commercial applications.
This Standard covers NPS-1/2 to NPS-2 zinc electroplated steel and non-electroplated stainless steel, double pipe union couplers intended for use in above or below ground pressure systems such as compressed air/pneumatic, gas, or water distribution systems. This standard specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers air admittance valves with adverse pressure seals and leak indication intended for applications in all plumbing systems including pumped waste and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers water meter air control valves in sizes NPS 1/2 to NPS 8 intended for use in commercial and residential water supply lines and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers NPS 1‐1/2 and NPS 2 diverting roof vent terminals intended for installation under solar panels to divert the outlet termination point of roof vent pipe or stack in residential and commercial buildings’ DWV systems, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers quality and performance requirements for quartz surfacing intended for horizontal and vertical interior applications and specifies minimum requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers pipe content warning disks (CWD) intended for installation in the cleanout of ABS, PVC and Cast Iron, drain waste and vent systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers snap-lock fittings made of ABS or PVC intended for DWV applications and specifies requirements for materials, dimensions and other physical characteristics, and markings.
This Standard covers flow control water conservation systems intended for residential and commercial water supply applications and specifies requirements for materials, physical characteristics, performance testing, and markings. Flow control water conservation systems designed to reduce water consumption, thereby, achieving water conservation, reducing gallons per minute in non‐volumetric applications during high periods of demand. An example of flow control water conservation systems covered by these standards is shown in Figure 1 and may be constructed, as follows:
- (a) Inlet and Outlet Pipe, Copper Type L;
- (b) Cast Copper Alloy Flanges, Soldered;
- (c) Butterfly Valves; and
- (d) Orifice Plate.
This Standard covers DN 40 to DN 200 or 1‐1/2 to 8 NPS polypropylene Drain, Waste and Vent (DWV) pipe with a mineral filled core and polypropylene fittings intended for use in commercial and residential applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard specifies test methods for measuring the performance, including the heat recovery efficiency and pressure loss, of sloped and vertical drain water heat recovery units. It is intended to serve as a performance assessment for producers, distributors, architects, code officials, contractors, installers and end users.
This Standard covers reversible 1‐1/4 and 1‐1/2 NTS plastic push fit tubular fittings intended for quick assembly of PVC and PP waste tubing and tubular fittings applications, and specifies requirements for materials, physical characteristics, performance testing, and markings.
This standard covers electronic plumbing supply system integrity detection devices for commercial and residential applications and specifies requirements for materials, physical characteristics, performance testing and markings.
This standard covers electronic plumbing supply system integrity detection devices for commercial and residential applications and specifies requirements for materials, physical characteristics, performance testing and markings.
This Standard covers 150 to 300 mm (6 to 12 in) diverter valves intended for diversion of rainwater or storm water for use in alternate nonpotable water source systems and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers branch connectors for NPS 1‐1/2 through 6 intended for hydronics, compressed gas and fire sprinkler applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers expandable pressure pipe renewal systems employing polyethylene terephthalate (PET) intended for use in water supply pipes ranging from DN 15 to 50 (1/2 to 2 NPS) and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers drain plates intended for commercial and residential water closets and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers flexible expansion couplings intended to be used as an expansion joint in stacked venting applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers compression fittings intended for water supply and exposed above ground gas distribution in residential, commercial, industry applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers continuous flexible self plunging waste pipes intended for connecting to lavatories and kitchen sinks; and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers compression molded corrugated thermoplastic septic tank, sewage holding tank, and effluent chamber applications specified under CSA B66 and specifies requirements for sizing, design, materials, physical characteristics, performance testing, markings and literature.
Note: This Standard supplements requirements for corrugated thermoplastic prefabricated septic tanks, sewage holding tanks, and effluent chambers specified under CSA B66. This standard is not intended to address corrugated thermoplastic prefabricated septic tanks, sewage holding tanks, and effluent chambers manufactured using molding techniques other than compression molding.
This Standard covers linear trench drains intended for elevator threshold applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers stainless steel sinks with integrated grease and solids recovery devices intended for commercial and residential kitchen applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers mechanical thermostatic balancing valves for hot water distribution intended commercial and residential applications and specifies requirements for materials, physical characteristics, performance testing, and markings. This Standard covers mechanical thermostatic balancing valves and does not cover any other balancing valves that require calibration (i.e., via pressure drop calibration or throttling).
This Standard covers point of entry regenerable (using dissolved oxygen) well water filtration systems intended for residential and commercial applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers atmospheric thermal storage devices intended for but not limited to space heating and cooling applications, hot water distribution without coming into contact with potable water, pool heating, and snow melting applications and specifies requirements for materials, physical characteristics, performance testing, and markings. This Standard does not cover products that come in contact with potable water.
This Standard covers point of use solids and grease collection devices intended for residential and commercial applications and specifies requirements for materials, physical characteristics, performance testing, and markings. This Standard covers a standalone point of use solids and grease collection devices, but it may also be used in conjunction with a larger centralized grease interceptor downstream when required by the code or the Authority Having Jurisdiction (AHJ).
This Standard applies to wastewater solid-liquid separators and optional complementary components used to assemble wastewater management systems, and specifies requirements for materials, physical characteristics, testing, and markings. The complementary components covered in this Standard are
(a) wastewater holding tanks;
(b) sewage pumps; and
(c) wastewater heat exchangers.
This Standard also specifies requirements for system accessories such as controllers, pipe, pipe fittings, and couplings, necessary for the complete installation of the system.
This Standard covers performance testing for products producing sterile or ultrapure water using tap water as a source. Ultrapure water parameters covered in this standard include conductivity, TDS, pH, TOC, Sodium, Chloride, Silica, Heterotrophic Plate Count (HPC) bacteria, Virus (MS‐2; ATCC 15597‐B1), and Endotoxin (from Escherichia coli ATCC 33780).
This Standard covers pour flush plastic latrine toilet fixtures intended for indoor, and outdoor applications, and specifies requirements for materials, construction, performance, testing, and markings.
This Standard covers digital mixing valves for recirculating hot water systems intended for multi-unit residential and commercial/institutional applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers the shower head reservoir for gravity fed water capturing devices intended for shower applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers tankless water heater drain pans and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers fixtures with integrated dishwashers for residential and commercial applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
This Standard covers two-stage toilet couplers intended for sanitary and waste applications and specifies requirements for materials, physical characteristics, performance testing, and markings.
Purchase IAPMO IGC 397-2024 Standard
Read Only
This Standard covers residential ozone generators for pools, spas, and hot tubs and
specifies requirements for materials, construction, performance, testing, and markings.
This Standard covers stub out fittings with various end connections and specifies requirements
for materials, physical characteristics, performance testing, and markings.